Date: Fri, 24 Apr 2020 10:36:23 +1000 From: Tom Storey <tom@...ap.net> To: Rich Felker <dalias@...c.org> Cc: musl@...ts.openwall.com Subject: Re: Building for m68k Thanks Rich. Just for gits and shiggles I tried #ifdef'ing out the cas.l instruction in the atomic_arch.h file for 68020+ processors, and compilation then proceeded along very smoothly for a while, but then hit another roadblock in src/setjmp/m68k/longjmp.s where it tries to execute a floating point instruction, and then subsequently fails with a "needs M68K fpu" error message. So maybe there was a way to work around that, but FPU adds another dimension to this problem. Trying to make this work is probably more than I'm really willing to take on for this project, so I may put it on the back burner and perhaps look at it another time. In the meantime I will look at copying in the source I require into my own "kind of mini-libc". I can't imagine I'm going to use a large percentage of what's there anyway, so maybe just cherry picking the bits I want is a better way forward for now. If I get really adventurous maybe I'll look into using a 68020 or above processor, but for now I would like to stick with the simpler 68000. At that point I could probably look at running more of a full blown Linux. :-) Cheers. On Fri, 24 Apr 2020 at 02:30, Rich Felker <dalias@...c.org> wrote: > On Thu, Apr 23, 2020 at 03:04:15PM +1000, Tom Storey wrote: > > Hi Rich, > > > > Sorry, I should perhaps mention that I am looking to "build for bare > > metal", if that matters? Im not a particular expert in all of this. :-) > > > > Basically, my situation is that Im a hobbyist, and have plans to build a > > computer around the m68k. Not looking to run Linux or anything on it, but > > dont want to be stuck with writing assembly. I was hoping to have libc > > available just to have access to some standard functions if needed. > > > > Or, perhaps Im complicating things for my intended use? The older CPUs > > might not be supported due to lack of MMU, and libc is really only meant > > for use within an OS environment? Could I perhaps be better off writing > my > > own implementations of libc things if/when I need them? > > It's possible to do a bare-metal port of musl, or to use unmodified or > minimally-modified musl with bare-metal by implementing the syscall > ABI for at least a minimal set of syscalls for things you need. In the > m68k case the latter would also involve the trap handler emulating the > cas instruction. If doing your own more extensive port, you could do > something more elaborate but less costly, or on nommu something simple > like cli;nonatomic_op;sti. > > Any of these options is going to be a lot less work than writing a > significantly functional libc from scratch. > > Rich > > > > On Thu, 23 Apr 2020 at 12:32, Rich Felker <dalias@...c.org> wrote: > > > > > On Thu, Apr 23, 2020 at 12:05:27PM +1000, Tom Storey wrote: > > > > Hi all. > > > > > > > > Is anyone out there particularly familiar with building musl for the > > > m68k? > > > > > > > > I was able to successfully build it, but then later discovered that > it > > > > would appear to be targeting 68020+ processors more specifically. I > would > > > > like to build for the earlier 6800's. > > > > > > > > Specific examples are to do with (at least) aio where some atomic > > > > instructions are used (e.g. cas - compare and swap) which only exist > for > > > > the 68020 and later, but not for earlier processors. > > > > > > > > https://git.musl-libc.org/cgit/musl/tree/src/aio/aio.c#n375 > > > > https://git.musl-libc.org/cgit/musl/tree/arch/m68k/atomic_arch.h > > > > > > > > Thus, adding -m68000 to the CFLAGS env variable when trying to do a > > > rebuild > > > > results in a failure complaining that the 68020+ is required. I dont > know > > > > what else is hiding away in the rest of it that will also be > > > > incompatible... :-) > > > > > > > > Any suggestions, pointers, tips would be greatly appreciated. > > > > > > To answer this I think we need to know how Linux support for these > > > models is meant to work (if it even is meant to). If Linux does > > > trap-and-emulate (I'm not aware of any other mechanism it has by which > > > it could make this work) then it might just amount to passing the > > > right -Wa,... to make the assembler accept instructions not supported > > > in the target ISA level. But it could mean there are missing > > > prerequisites that have to be fixed on the kernel side before anything > > > can actually work. > > > > > > Rich > > > > Content of type "text/html" skipped
Powered by blists - more mailing lists
Confused about mailing lists and their use? Read about mailing lists on Wikipedia and check out these guidelines on proper formatting of your messages.